Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
Are you currently in search of critical info on Installing A Bathtub?
Setting up a bathtub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is easily accessible, the job can move easily; if you have to open up a wall to remove the old bathtub and position the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to vacate the old tub and embeded in the new one. Make sure you have actually qualified yourself for the task and fit attempting it. Rather than employing a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly aid you mount a new bathtub in your restroom if you have already gotten a brand-new bathtub and also do not need to change the setup of your previous water pipelines.
Your devices and material list need to comprise the following:
Planning for the Installment
First of all, the sustaining framework provided with the bathroom must be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. When the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using both wood boards under its feet, place the bath tub in the needed placement. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bathtub till the spirit level checks out level.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leakages and also tighten them if required. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait till the bathtub has been made use of at least once as this will certainly resolve it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location in between the faucet as well as the sink. Protect the faucet in position with the supplier given backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous kind must be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with dampness and also feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes as well as cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the tub with water before sealing, to enable the movement experienced when the tub remains in usage. The sealant can crack fairly very early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that write up on How to Install a Bathtub while doing research the web. Do you know about anybody else who is fascinated about the subject? Do not hesitate to share it. Thank-you for going through it.
Article
Report this page